Press Center
 
Home About us Products Support Quality & Certification Career Contact us
• Power Management
    Linear Regulators
    Low Dropout Linear Regulators
    DDR Termination Regulators
    Shunt Reference Regulators
    Step Down Switching Regulators
    Switching Regulator
    Step-Up DC-DC Converter
    PWM Controller
    White LED Driver
    Supervisory Circuit
    Voltage Detection and System R
    USB Power Switch
    Power Factor Control
    Li-Battery Protection or Charg
    FET Bias Controllers
    Combo IC
    Inverting DC-DC Converter
• Amplifier / Comparator
    Audio Amplifiers
    Operational Amplifier
    Voltage Comparator
• Analog Switches
    Video Signal Switch
    Analog Multiplexers, Demultipl
• Hall ICs
• Special Application ICs
    Motor Controller IC
    Interface and Driver Circuit
    Telecommunication Circuit
    Melody IC
    Alarm /Sound Generator IC
    Remote Controller IC
    Television Circuit
    Leakage Current Detector
    Automotive IC
    A-D or D-A Converters
    Miscellaneous
    Radio and Cassette Recorder Ci
    Timer
    Mouse&Keyboard Controller
    Transient Voltage Suppressors
    Sense Monitor
    Video Filter
    ZCB snubber
• Logic
• TRANSISTORs
• MOSFETs
    JFET
    Power Mosfet
• TRIACs
• SCRs
• DIODEs
 
Home >
U74HCT7046 Datasheet
PHASE LOCKED LOOP WITH VCO & LOCK DETECTOR
 
 
 
DESCRIPTION
 
The U74HCT7046 is phase-locked-loop circuit that comprise a linear
voltage-controlled oscillator (VCO), two-phase comparators (PC1, PC2),
a lock detector, a common signal input amplifier and a common
comparator input.
The lock detector capacitor should be connected between pin
15(CLD) and pin 8(GND).For a frequency range of 100kHz to 10MHz,the
lock detector capacitor must be 1000pF to 10pF,respectively.
The signal can be directly coupled to large voltage signals, or with a
series capacitor coupled to small signals. Small voltage signals can be
kept within the linear region of the input amplifiers with a self-bias input
circuit. The U74HCT7046 and a passive low-pass filter form a
second-order loop PLL. With a linear op-amp, the VCO achieves
excellent linearity.
The VCO requires external capacitor and resistor. R1 (between R1
and GND) and capacitor C1 (between C1A and C1B) determine the
frequency range of the VCO. R2 (between R2 and GND) enables the
VCO to have a frequency offset if required.
 
For the high input impedance of the VCO, the design of low-pass filters is simplified, and the designer has a wide
choice of resistor/capacitor ranges. At pin 10 (DEMOUT), a demodulator output of the VCO input voltage is provided
in order not to load the low-pass filter. In conventional techniques, the DEMOUT voltage is one threshold voltage
lower than the VCO input voltage, but the DEMOUT voltage of U74HCT7046 equals the VCO input voltage. When
DEMOUT is used, a load resistor (RS) should be connected from DEMOUT to GND; but if unused, DEMOUT should be left open. The VCO output (VCOOUT) can be connected directly or via a frequency-divider to the comparator input
(COMPIN). If the VCO input is held at a constant DC level, the VCO output signal has a duty factor of 50%
(maximum expected deviation 1%). A LOW level at the inhibit input (INH) enables the VCO and demodulator, while
a HIGH level turns both off to minimize standby power consumption.
 
 
 
FEATURES
 
 
* Operating Power Supply Voltage Range: Digital Section 4.5 to 5.5 V
VCO Section 4.5 to 5.5 V
* Up to 18 MHz (typ.) Centre Frequency at VCC = 5V
* Excellent VCO Frequency Linearity
* VCO-Inhibit Control For ON/OFF Keying and for Low Standby Power Consumption
* Minimal Frequency Drift
* Zero Voltage Offset due to OP-Amp Buffering
About us  |  Products  |  Contact us
Copyright 2011 UTC All received